100W backpack pulse laser cleaning machine rust removal-manufacture,factory,supplier from China

Laser cutting machine maintenance and cleaning skillsLaser cutting is the laser beam irradiated to the workpiece surface through the release of energy to melt and evaporate the workpiece, in order to achieve the purpose of cutting and engraving process. With high precision, fast cutting, and not limited to the cutting pattern limit, automatic typesetting save materials, smooth incision, low processing costs, will gradually improve or replace the traditional cutting process equipment.

Laser cutting machine maintenance and cleaning skillsLaser cutting is the laser beam irradiated to the workpiece surface through the release of energy to melt and evaporate the workpiece, in order to achieve the purpose of cutting and engraving process. With high precision, fast cutting, and not limited to the cutting pattern limit, automatic typesetting save materials, smooth incision, low processing costs, will gradually improve or replace the traditional cutting process equipment.

The control part of pulsed laser power supply mainly consists of signal source, signal processing and delay regulation, pulse power amplification, energy storage voltage control and other circuits. The main circuit structure of the pulsed laser power supply we developed adopts resonant switching technology, which can be closed when the current passes zero, effectively reducing the switching loss and improving the conversion efficiency.

What are the differences between the QCW, CW and PW working modes of laser source?Laser source is a device that transfers energy from an active medium to an output beam. The working mode of the laser source has an important impact on the performance and application of the laser source. In the operation of laser source, QCW (pulse modulation width), CW (continuous wave) and PW (pulse wave) are common operating modes.

Source of electrical noiseNoise is generated when there is a rapid jump in the voltage or current waveform. In a switching power supply, many waveforms are periodic, that is, pulses containing high frequency edges repeat at a predictable pulse repetition rate (PRF). For a rectangular pulse train, the reciprocal of the period determines the fundamental frequency of the waveform. The Fourier transform of a rectangular wave contains a large number of harmonics at the fundamental frequency.

Mode of operation of laserThe laser with different wavelength and different output mode will be absorbed by different tissues or substances after entering the skin and thus produce different action modes. These tissues or substances are called Chromophore.Photothermal action refers to the absorption of laser light into the skin by specific pigment groups and then converted into heat energy. Depending on the duration of the laser pulse and the heat dissipation time of the skin tissue, the heat may spread to the surrounding tissues and cause a wide range of heating (e.g.

Laser engraving machine use precautions1. When using automatic focal length, it is necessary to pay attention to whether the automatic focal rod is fastened. If the automatic focal rod is loose, it will cause the top of the workbench to the laser.2. When laser engraving machine is working, it is forbidden to open the boot cover.3. Open the smoke exhaust and smoke blowing equipment during processing.4, processing wood, paper, must pay attention to the processing speed to avoid fire.5.

Laser engraving machine maintenance guide1, laser engraving machine in the process of use should be strictly in accordance with the correct startup order to open or close the equipment (note: laser power must be preheated for 5 minutes!) .2, in the process of laser engraving machine, must be at any time to detect the water temperature (the best working water temperature is 25~30℃, the highest water temperature can not exceed 35℃, the lowest water temperature can not be less than 5℃), once the water temperature is high, should immediately change the water.

Laser cutting machine equipment common faults and solutions1, boot without any response▶ Power fuse is burnt out: Replace the fuse.▶ Power input is normal: Check power input and make it normal.▶ Main power switch is damaged: Replace the main power switch.2, no laser output or very weak laser▶ Optical path offset: Carefully adjust the optical path.▶ Contaminated or damaged reflector lens: Clean or replace reflector lens.▶ Whether the focal length of the device is changed: readjust the focal length.▶ Focusing mirror is contaminated: Clean the focusing mirror.▶ Cooling water quality or temperatur

Laser engraving machine in the process of the use of skillsBefore starting work, you should carefully check the spelling of the text portion of the engraving project, and if conditions permit, print the contents and confirm with the customer. If you want to avoid the dislocation of the sculpture in the process of engraving, you need to do a good job of prevention, and implement the corresponding solution when the dislocation problem occurs.Error checking:a. Check whether the pliers or clamp used for engraving are wrongb. Whether the pliers or clips are wornc.