200W backpack pulse laser cleaning machine rust removal - Bulk Cloned-manufacture,factory,supplier from China

Laser cutting machine maintenance and cleaning skillsLaser cutting is the laser beam irradiated to the workpiece surface through the release of energy to melt and evaporate the workpiece, in order to achieve the purpose of cutting and engraving process. With high precision, fast cutting, and not limited to the cutting pattern limit, automatic typesetting save materials, smooth incision, low processing costs, will gradually improve or replace the traditional cutting process equipment.

Laser cutting machine maintenance and cleaning skillsLaser cutting is the laser beam irradiated to the workpiece surface through the release of energy to melt and evaporate the workpiece, in order to achieve the purpose of cutting and engraving process. With high precision, fast cutting, and not limited to the cutting pattern limit, automatic typesetting save materials, smooth incision, low processing costs, will gradually improve or replace the traditional cutting process equipment.

The control part of pulsed laser power supply mainly consists of signal source, signal processing and delay regulation, pulse power amplification, energy storage voltage control and other circuits. The main circuit structure of the pulsed laser power supply we developed adopts resonant switching technology, which can be closed when the current passes zero, effectively reducing the switching loss and improving the conversion efficiency.

Mode of operation of laserThe laser with different wavelength and different output mode will be absorbed by different tissues or substances after entering the skin and thus produce different action modes. These tissues or substances are called Chromophore.Photothermal action refers to the absorption of laser light into the skin by specific pigment groups and then converted into heat energy. Depending on the duration of the laser pulse and the heat dissipation time of the skin tissue, the heat may spread to the surrounding tissues and cause a wide range of heating (e.g.

What are the differences between the QCW, CW and PW working modes of laser source?Laser source is a device that transfers energy from an active medium to an output beam. The working mode of the laser source has an important impact on the performance and application of the laser source. In the operation of laser source, QCW (pulse modulation width), CW (continuous wave) and PW (pulse wave) are common operating modes.

Laser engraving machine use precautions1. When using automatic focal length, it is necessary to pay attention to whether the automatic focal rod is fastened. If the automatic focal rod is loose, it will cause the top of the workbench to the laser.2. When laser engraving machine is working, it is forbidden to open the boot cover.3. Open the smoke exhaust and smoke blowing equipment during processing.4, processing wood, paper, must pay attention to the processing speed to avoid fire.5.

How to install laser engraving machineThe installation of laser engraving machine has the following three steps:1. Installation(1) Insert the control card into the microcomputer PCI slot, tighten the screws, and connect the data cable; Plug in the USB dongle and install the operating software and dongle driver.(2) Connect the laser tube water circulation tube with the anode and cathode conductor, and then put the laser tube clamp ring.

Laser engraving machine maintenance guide1, laser engraving machine in the process of use should be strictly in accordance with the correct startup order to open or close the equipment (note: laser power must be preheated for 5 minutes!) .2, in the process of laser engraving machine, must be at any time to detect the water temperature (the best working water temperature is 25~30℃, the highest water temperature can not exceed 35℃, the lowest water temperature can not be less than 5℃), once the water temperature is high, should immediately change the water.

Laser cutting machine equipment common faults and solutions1, boot without any response▶ Power fuse is burnt out: Replace the fuse.▶ Power input is normal: Check power input and make it normal.▶ Main power switch is damaged: Replace the main power switch.2, no laser output or very weak laser▶ Optical path offset: Carefully adjust the optical path.▶ Contaminated or damaged reflector lens: Clean or replace reflector lens.▶ Whether the focal length of the device is changed: readjust the focal length.▶ Focusing mirror is contaminated: Clean the focusing mirror.▶ Cooling water quality or temperatur

How to prolong the service life of laser tube1 laser engraving machine, cutting machine in the use of laser tube, need to pay attention to the best use of pure cooling water, and keep the water temperature below 25℃.2. Summer temperature is high, it is necessary to pay attention to frequently change the cooling water, found that the temperature is too high, need to stop and rest and replace the cooling water; Winter temperature is low, the machine after the completion of the work, need to put the laser tube internal cooling water, to avoid the laser tube is frozen cracked.3.