500-100000W Fiber Laser Drive System-manufacture,factory,supplier from China

Ultrasonic generator common failure and maintenance methodsUltrasonic generator is a kind of equipment that converts the mains power into the corresponding high-frequency alternating current of the transducer to drive the transducer to work. It is an important component of the high-power ultrasonic system. It can also be called electronic box, ultrasonic driving power supply and ultrasonic controller. Although the ultrasonic generator can also be called the ultrasonic drive power, but in fact, the ultrasonic generator is only a part of the ultrasonic drive power.

Application of semiconductor laser power supplySemiconductor laser market leading fiber laser, gas laser, solid laser market for a while, and several other categories of laser market proportion is similar. However, since 2016, the market share of semiconductor laser has expanded rapidly, with an annual growth rate of 170%. In 2015 and 2015, semiconductor laser accounted for 50% of the total market share of laser. The market share of semiconductor laser power supply also expanded at the same time.

Laser operators should have the relevant technical knowledge of laser power supply system. If the large-scale laser power supply system has an emergency situation during operation, the laser operators should diagnose and repair the fault as soon as possible to ensure the normal operation of the laser system. There are many reasons for the power problems of laser power supply. Here, we will list the following five problems which are easy to appear in the operation of laser system for discussion.1.

How to repair the failure of CO2 laser power supply?CO2 laser is widely used in laser engraving, laser cutting and other fields, mainly composed of luminescence system, motion system, control system. Next, our company will briefly introduce how to judge and troubleshoot the failure of CO2 laser power supply from the following two aspects.Laser has no laser output1. Check whether the laser tube itself is illuminated (test whether it is illuminated at the optical outlet of the laser tube). If it is illuminated normally, check whether the lens is damaged and the optical path is offset.2.

Laser power supply technicians are important members of the operation of laser equipment, but in the operation of laser power supply, will also encounter all kinds of difficulties, today we summarized some of the first-line manufacturers of technical personnel to provide common problems to discuss with you:▲ Power failure:Problems occur: Because the laser power supply system, especially the high-power laser power supply system requires a large amount of voltage, if the voltage is not stable, it will produce inconsistent output power, resulting in catastrophic damage.Solution: If you do not hav

Laser power supply technician is an important member of the operation of equipment, but in the operation of laser power supply, will also encounter a variety of difficult problems, today our factory technicians summed up the following problems, and according to the problem one by one to solve the problem, these problems are very key, I hope to pay attention to.▲ Power failure: Because the laser power supply system, especially the high-power laser power supply system needs a lot of voltage, the power supply related problems will produce inconsistent output power, leading to catastrophic damage.

Mode of operation of laserThe laser with different wavelength and different output mode will be absorbed by different tissues or substances after entering the skin and thus produce different action modes. These tissues or substances are called Chromophore.Photothermal action refers to the absorption of laser light into the skin by specific pigment groups and then converted into heat energy. Depending on the duration of the laser pulse and the heat dissipation time of the skin tissue, the heat may spread to the surrounding tissues and cause a wide range of heating (e.g.

The principle of laser generationLASER is written as "Light Amplification by Stimulated Emission of Radiation", which means that by the principle of "excitation emission", the amplification of light waves is generated, which is called "laser". The motion state of electrons can be divided into different energy levels. When electrons transition from high energy level to low energy level, they will release electromagnetic waves of corresponding energy (the so-called spontaneous radiation).

As early as 1983, a scientific paper posted by way of two scholars, Anderson and Parrish, proposed "selective photothermal decomposition". This is a very necessary thought for the improvement and software of laser in dermatology.

How to prolong the service life of laser tube1 laser engraving machine, cutting machine in the use of laser tube, need to pay attention to the best use of pure cooling water, and keep the water temperature below 25℃.2. Summer temperature is high, it is necessary to pay attention to frequently change the cooling water, found that the temperature is too high, need to stop and rest and replace the cooling water; Winter temperature is low, the machine after the completion of the work, need to put the laser tube internal cooling water, to avoid the laser tube is frozen cracked.3.