AC plasma incinerator power supply-manufacture,factory,supplier from China

Classification of switching power suppliesSwitching power supplies can be divided into AC/DC and DC/DC. As a secondary power supply, DC/DC converter has realized modularization, and the design technology and production process have been mature and standardized at home and abroad, and has been recognized by users. However, due to its own characteristics, the primary power AC/DC has encountered more complex technical problems and manufacturing problems in the process of modularization.

Technical Trends of Switching Power Supply AbroadSince the 1990s, the development of switching power supply has changed with each passing day. Many new fields and new requirements put forward newer and higher challenges to switching power supply. If we observe from the input and output window of a switching power supply, we can find that the input requirements have become more stringent, and products that do not meet the IEC1000-3-2 standard will be gradually eliminated; The output has derived many special application fields, and the difficulty of research and development has become greater.

Various techniques for switching power supplies to reduce lossesThe efficiency of PWM switching power supply without special loss control technology is lower than that of switching power supply with loss control technology. For switching power supplies that have no problem with heat dissipation, such as some off-line power supplies, the efficiency may be satisfactory. But for portable power supplies and devices requiring small size, greater efficiency must be sought.

Switch power output protection policyIn all switching power supply designs, protection against load and protection against power supply due to load failure is a very important aspect to be considered in the design. In the design of military products, a kind of work called failure mode and impact analysis is often required. In this work, each part of the circuit is assumed to be an open circuit fault and then a short circuit fault. In this case, analyze separately how each fault will affect the rest of the circuit.

The basic principle of PWM switching power supplyAlthough pulse-width-modulated (PWM) switching power supplies have been around for a long time, they were not widely accepted and used until the mid-1970s. Switching power supplies have many advantages over linear power supplies.For the same power capacity, switching power supplies are more efficient and smaller than linear power supplies, but the design is more complex and electromagnetic interference (EMI) is more severe.There are two approaches to the current design of switching power supplies.

How to use high voltage power supply to detect high voltage cablesTo ensure the normal and safe use of high-voltage cables, check the cable inlet before or after using them for a period of time. The test includes determining whether the main insulation is damp or aging, and checking whether there are defects in the main insulation of the cable after the voltage test. High voltage power supply is the main tool used for voltage resistance and insulation detection of cable.The source of Radium specially produced a power supply type for the high voltage test of power supply :HY-12KV and HY-32KV.

Power supply circuit analysis of pulsed semiconductor laserPulsed semiconductor lasers have the advantages of high peak power and small size, and are widely used in the fields of laser ranging, lidar and free space laser communication.

Laser operators should have the relevant technical knowledge of laser power supply system. If the large-scale laser power supply system has an emergency situation during operation, the laser operators should diagnose and repair the fault as soon as possible to ensure the normal operation of the laser system. There are many reasons for the power problems of laser power supply. Here, we will list the following five problems which are easy to appear in the operation of laser system for discussion.1.

Power supply precautions and fault detection methods of laser cutting machineLaser cutting machine power use precautionsLaser cutting machine in the process of use, to the various components of the equipment for good maintenance, to ensure the normal operation of the machine. Laser power supply is one of the most important parts in laser cutting machine equipment, improper use is easy to cause damage to the power supply, affect the normal production.

Laser power supply technician is an important member of the operation of equipment, but in the operation of laser power supply, will also encounter a variety of difficult problems, today our factory technicians summed up the following problems, and according to the problem one by one to solve the problem, these problems are very key, I hope to pay attention to.▲ Power failure: Because the laser power supply system, especially the high-power laser power supply system needs a lot of voltage, the power supply related problems will produce inconsistent output power, leading to catastrophic damage.