Fiber laser main control board-manufacture,factory,supplier from China

The control part of pulsed laser power supply mainly consists of signal source, signal processing and delay regulation, pulse power amplification, energy storage voltage control and other circuits. The main circuit structure of the pulsed laser power supply we developed adopts resonant switching technology, which can be closed when the current passes zero, effectively reducing the switching loss and improving the conversion efficiency.

Application of semiconductor laser power supplySemiconductor laser market leading fiber laser, gas laser, solid laser market for a while, and several other categories of laser market proportion is similar. However, since 2016, the market share of semiconductor laser has expanded rapidly, with an annual growth rate of 170%. In 2015 and 2015, semiconductor laser accounted for 50% of the total market share of laser. The market share of semiconductor laser power supply also expanded at the same time.

Laser cutting machine equipment common faults and solutions1, boot without any response▶ Power fuse is burnt out: Replace the fuse.▶ Power input is normal: Check power input and make it normal.▶ Main power switch is damaged: Replace the main power switch.2, no laser output or very weak laser▶ Optical path offset: Carefully adjust the optical path.▶ Contaminated or damaged reflector lens: Clean or replace reflector lens.▶ Whether the focal length of the device is changed: readjust the focal length.▶ Focusing mirror is contaminated: Clean the focusing mirror.▶ Cooling water quality or temperatur

Design of a low power semiconductor laser driving power supplyWith the semiconductor in communication, measurement and control, medical, integrated optics and other technical fields of wide application, its attention is also increasing, for the design of a high precision, reliable performance, economic, durable driving power has become our current most urgent problem, because of the semiconductor laser "delicate" characteristics, the use of power must be in the performance and quality of strict control. Transfer characteristics of semiconductor lasersAt a certain temperature, wh

How to install laser engraving machineThe installation of laser engraving machine has the following three steps:1. Installation(1) Insert the control card into the microcomputer PCI slot, tighten the screws, and connect the data cable; Plug in the USB dongle and install the operating software and dongle driver.(2) Connect the laser tube water circulation tube with the anode and cathode conductor, and then put the laser tube clamp ring.

Laser power supply is the energy of laser, it provides pumping energy to laser, control laser output strength and repetition frequency. Therefore, laser power supply is an essential part of laser. Its power and stability have direct influence on the corresponding performance of laser. The current output of a power box is designed according to the requirements of the pump module.

Various techniques for switching power supplies to reduce lossesThe efficiency of PWM switching power supply without special loss control technology is lower than that of switching power supply with loss control technology. For switching power supplies that have no problem with heat dissipation, such as some off-line power supplies, the efficiency may be satisfactory. But for portable power supplies and devices requiring small size, greater efficiency must be sought.

Carbon dioxide laser is a gas laser with CO2 gas as the main working substance (CO2: N2: He=1:7:20). The CO2 laser consists of a discharge tube, a resonator and an electrode. With the addition of a DC high voltage pump, the gas in the discharge tube emits light (the output wavelength is 10.6μm).

How to use high voltage power supply to detect high voltage cablesTo ensure the normal and safe use of high-voltage cables, check the cable inlet before or after using them for a period of time. The test includes determining whether the main insulation is damp or aging, and checking whether there are defects in the main insulation of the cable after the voltage test. High voltage power supply is the main tool used for voltage resistance and insulation detection of cable.The source of Radium specially produced a power supply type for the high voltage test of power supply :HY-12KV and HY-32KV.

How to repair the failure of CO2 laser power supply?CO2 laser is widely used in laser engraving, laser cutting and other fields, mainly composed of luminescence system, motion system, control system. Next, our company will briefly introduce how to judge and troubleshoot the failure of CO2 laser power supply from the following two aspects.Laser has no laser output1. Check whether the laser tube itself is illuminated (test whether it is illuminated at the optical outlet of the laser tube). If it is illuminated normally, check whether the lens is damaged and the optical path is offset.2.