fifty three mw output en-manufacture,factory,supplier from China

Switch power output protection policyIn all switching power supply designs, protection against load and protection against power supply due to load failure is a very important aspect to be considered in the design. In the design of military products, a kind of work called failure mode and impact analysis is often required. In this work, each part of the circuit is assumed to be an open circuit fault and then a short circuit fault. In this case, analyze separately how each fault will affect the rest of the circuit.

How to install laser engraving machineThe installation of laser engraving machine has the following three steps:1. Installation(1) Insert the control card into the microcomputer PCI slot, tighten the screws, and connect the data cable; Plug in the USB dongle and install the operating software and dongle driver.(2) Connect the laser tube water circulation tube with the anode and cathode conductor, and then put the laser tube clamp ring.

A photon is an fundamental particle, a quantum of electromagnetic radiation. In quantum subject theory, it is the pressure provider that transmits the electromagnetic force.Light spots/spots are few and a ways betweenLight spot is the contact factor of mild contact skin, distinctive units have specific mild output measurement and shape.

Switch regulator based on LCbuck converters are much like barrel regulators, except that inductors replace resistors and a "new" diode is added. If we can understand the function of the diode, we can understand the basic principle of various power converters more clearly. This diode is called a clamp diode, a continuation diode, a commutator diode, or an output diode.

Why the laser is weak or has no laser outputWhether the focusing mirror is contaminated: Clean the focusing mirror.Whether the focal length of relief engraving machine equipment changes: readjust the focal length.Whether the optical path is offset: Adjust the optical path carefully.Whether the reflector is contaminated or damaged: Clean or replace the reflector.Whether the laser power supply is powered on: Check the power supply loop of the laser power supply to make it normal.Whether the laser tube is damaged or aged: Replace the laser tube.Whether the laser power supply is damaged: Replace t

Optical terms for cosmetic instrumentsA photon is an elementary particle, a quantum of electromagnetic radiation. In quantum field theory, it's the force carrier that transmits the electromagnetic force.Light spots/spots are few and far betweenLight spot is the contact point of light contact skin, different instruments have different light output size and shape. Such as color light instrument contact point is generally rectangular, size marked as long x wide (for example: 10mm x 25mm). Generally, the laser output is a dot, and the size is marked as the diameter (e.g., 3mm, 8mm, etc.).

Selection and use of semiconductor laser power supplyFirst, the basic requirements of semiconductor laser power supply1. Constant current output: short-circuit constant current output, load changes or short-circuit automatic adaptation.2. Output current ripple: ripple, noise and rated output current cannot exceed the maximum current that the laser tube can bear.3. Output voltage ripple: Ripple voltage noise will not damage the laser immediately, but if serious, it will affect the life of the laser.4. Soft start: Slow start current curve, no overshoot.5.

Distinguish different cosmetic optical instruments and their functionsThere are many different optical instruments on the market, which give off different frequency and characteristics of the radiation wave. We can basically tell by its wavelength, energy, output mode, etc.Ultraviolet lightUltraviolet light can be divided into ultraviolet A, ultraviolet B and ultraviolet C according to different wavelengths. Uv A has a wavelength between 315-400 nm.

Along with the continuous development of economy in our country, most areas begin to produce electric power equipment, which makes the national grid electric power output insufficient, coupled with the aging of the power output facilities, eventually causes the voltage at the end of the circuit to be too low, which brings great influence on the stability of laser output. The stable output of laser energy is a necessary condition for laser production.

What are the differences between the QCW, CW and PW working modes of laser source?Laser source is a device that transfers energy from an active medium to an output beam. The working mode of the laser source has an important impact on the performance and application of the laser source. In the operation of laser source, QCW (pulse modulation width), CW (continuous wave) and PW (pulse wave) are common operating modes.