Laser Machine Power Supply-manufacture,factory,supplier from China

Power supply precautions and fault detection methods of laser cutting machineLaser cutting machine power use precautionsLaser cutting machine in the process of use, to the various components of the equipment for good maintenance, to ensure the normal operation of the machine. Laser power supply is one of the most important parts in laser cutting machine equipment, improper use is easy to cause damage to the power supply, affect the normal production.

Laser cutting machine equipment common faults and solutions1, boot without any response▶ Power fuse is burnt out: Replace the fuse.▶ Power input is normal: Check power input and make it normal.▶ Main power switch is damaged: Replace the main power switch.2, no laser output or very weak laser▶ Optical path offset: Carefully adjust the optical path.▶ Contaminated or damaged reflector lens: Clean or replace reflector lens.▶ Whether the focal length of the device is changed: readjust the focal length.▶ Focusing mirror is contaminated: Clean the focusing mirror.▶ Cooling water quality or temperatur

Why the laser is weak or has no laser outputWhether the focusing mirror is contaminated: Clean the focusing mirror.Whether the focal length of relief engraving machine equipment changes: readjust the focal length.Whether the optical path is offset: Adjust the optical path carefully.Whether the reflector is contaminated or damaged: Clean or replace the reflector.Whether the laser power supply is powered on: Check the power supply loop of the laser power supply to make it normal.Whether the laser tube is damaged or aged: Replace the laser tube.Whether the laser power supply is damaged: Replace t

Laser engraving machine maintenance guide1, laser engraving machine in the process of use should be strictly in accordance with the correct startup order to open or close the equipment (note: laser power must be preheated for 5 minutes!) .2, in the process of laser engraving machine, must be at any time to detect the water temperature (the best working water temperature is 25~30℃, the highest water temperature can not exceed 35℃, the lowest water temperature can not be less than 5℃), once the water temperature is high, should immediately change the water.

Laser cutting machine maintenance and cleaning skillsLaser cutting is the laser beam irradiated to the workpiece surface through the release of energy to melt and evaporate the workpiece, in order to achieve the purpose of cutting and engraving process. With high precision, fast cutting, and not limited to the cutting pattern limit, automatic typesetting save materials, smooth incision, low processing costs, will gradually improve or replace the traditional cutting process equipment.

Laser cutting machine maintenance and cleaning skillsLaser cutting is the laser beam irradiated to the workpiece surface through the release of energy to melt and evaporate the workpiece, in order to achieve the purpose of cutting and engraving process. With high precision, fast cutting, and not limited to the cutting pattern limit, automatic typesetting save materials, smooth incision, low processing costs, will gradually improve or replace the traditional cutting process equipment.

Laser power supply technician is an important member of the operation of equipment, but in the operation of laser power supply, will also encounter a variety of difficult problems, today our factory technicians summed up the following problems, and according to the problem one by one to solve the problem, these problems are very key, I hope to pay attention to.▲ Power failure: Because the laser power supply system, especially the high-power laser power supply system needs a lot of voltage, the power supply related problems will produce inconsistent output power, leading to catastrophic damage.

Laser engraving machine use precautions1. When using automatic focal length, it is necessary to pay attention to whether the automatic focal rod is fastened. If the automatic focal rod is loose, it will cause the top of the workbench to the laser.2. When laser engraving machine is working, it is forbidden to open the boot cover.3. Open the smoke exhaust and smoke blowing equipment during processing.4, processing wood, paper, must pay attention to the processing speed to avoid fire.5.

Technical Trends of Switching Power Supply AbroadSince the 1990s, the development of switching power supply has changed with each passing day. Many new fields and new requirements put forward newer and higher challenges to switching power supply. If we observe from the input and output window of a switching power supply, we can find that the input requirements have become more stringent, and products that do not meet the IEC1000-3-2 standard will be gradually eliminated; The output has derived many special application fields, and the difficulty of research and development has become greater.

Development of CO2 laser power supplyCO2 laser power supply accompanied with the development of CO2 laser, the initial application in the 1970s, and later with the progress of technology, the application field continues to expand.