Problem Laser Engraving Machine Power Supply-manufacture,factory,supplier from China

Laser engraving machine in the process of the use of skillsBefore starting work, you should carefully check the spelling of the text portion of the engraving project, and if conditions permit, print the contents and confirm with the customer. If you want to avoid the dislocation of the sculpture in the process of engraving, you need to do a good job of prevention, and implement the corresponding solution when the dislocation problem occurs.Error checking:a. Check whether the pliers or clamp used for engraving are wrongb. Whether the pliers or clips are wornc.

Laser engraving machine maintenance guide1, laser engraving machine in the process of use should be strictly in accordance with the correct startup order to open or close the equipment (note: laser power must be preheated for 5 minutes!) .2, in the process of laser engraving machine, must be at any time to detect the water temperature (the best working water temperature is 25~30℃, the highest water temperature can not exceed 35℃, the lowest water temperature can not be less than 5℃), once the water temperature is high, should immediately change the water.

How to install laser engraving machineThe installation of laser engraving machine has the following three steps:1. Installation(1) Insert the control card into the microcomputer PCI slot, tighten the screws, and connect the data cable; Plug in the USB dongle and install the operating software and dongle driver.(2) Connect the laser tube water circulation tube with the anode and cathode conductor, and then put the laser tube clamp ring.

Laser engraving machine use precautions1. When using automatic focal length, it is necessary to pay attention to whether the automatic focal rod is fastened. If the automatic focal rod is loose, it will cause the top of the workbench to the laser.2. When laser engraving machine is working, it is forbidden to open the boot cover.3. Open the smoke exhaust and smoke blowing equipment during processing.4, processing wood, paper, must pay attention to the processing speed to avoid fire.5.

The reason why the laser head of laser engraving machine does not glowIn the daily use of laser engraving machine, it is often encountered that the laser head of the laser engraving machine does not glow. This article briefly introduces how to deal with the laser head of the laser engraving machine.1.

Power supply precautions and fault detection methods of laser cutting machineLaser cutting machine power use precautionsLaser cutting machine in the process of use, to the various components of the equipment for good maintenance, to ensure the normal operation of the machine. Laser power supply is one of the most important parts in laser cutting machine equipment, improper use is easy to cause damage to the power supply, affect the normal production.

Laser power supply technician is an important member of the operation of equipment, but in the operation of laser power supply, will also encounter a variety of difficult problems, today our factory technicians summed up the following problems, and according to the problem one by one to solve the problem, these problems are very key, I hope to pay attention to.▲ Power failure: Because the laser power supply system, especially the high-power laser power supply system needs a lot of voltage, the power supply related problems will produce inconsistent output power, leading to catastrophic damage.

Why the laser is weak or has no laser outputWhether the focusing mirror is contaminated: Clean the focusing mirror.Whether the focal length of relief engraving machine equipment changes: readjust the focal length.Whether the optical path is offset: Adjust the optical path carefully.Whether the reflector is contaminated or damaged: Clean or replace the reflector.Whether the laser power supply is powered on: Check the power supply loop of the laser power supply to make it normal.Whether the laser tube is damaged or aged: Replace the laser tube.Whether the laser power supply is damaged: Replace t

Various techniques for switching power supplies to reduce lossesThe efficiency of PWM switching power supply without special loss control technology is lower than that of switching power supply with loss control technology. For switching power supplies that have no problem with heat dissipation, such as some off-line power supplies, the efficiency may be satisfactory. But for portable power supplies and devices requiring small size, greater efficiency must be sought.

Laser cutting machine maintenance and cleaning skillsLaser cutting is the laser beam irradiated to the workpiece surface through the release of energy to melt and evaporate the workpiece, in order to achieve the purpose of cutting and engraving process. With high precision, fast cutting, and not limited to the cutting pattern limit, automatic typesetting save materials, smooth incision, low processing costs, will gradually improve or replace the traditional cutting process equipment.